Printer Cleaning Kit | Printhead Cleaning Kit | for Inkjet Printers HP/Brother/Epson/Canon WF-7710 WF-3640 7620 8600 8610 8620 WF-2750 WF-2650 ET-2750 ET-2650 C88 Liquid Printers Nozzle（100ml）

It worked great on my Brother Inkvestment printer - which I don't think was listed as compatible.BE PATIENT and STAY THE COURSE! It's worth it to fix your broken, clogged-inkheads-printer!It took me a long time to even work up the nerve and find the time to try this, but I finally did. FIRST, I READ THE INSTRUCTIONS ALL THE WAY THROUGH - that's so important! Then I watched several youtube videos, trying to find a printer that looked kind of close to mine. On my first attempt, I was certain I had broken my printer in five ways - but as it turned out I didn't.I had to repeat the process somewhere between 12 and 15 times. Little by little my printheads became unclogged after sitting for 18 months unusable.I read several other reviews before settling on this product. Some of the reviews have good advice and clear guidance for fixing your printer. Here are some of those tips I found most helpful:1) Buy blotter paper to absorb the solution under the printhead. For my printer, I cut the blotter paper into thirds and wrapped a half-sheet of paper towel around it. TOTALLY NECESSARY.2) Put a towel under the printer. For me, this turned out to be an unnecessary step, but having the towel down relieved some of my stress - I didn't want a bunch of inky solution running all over my floor. That never happened, but that towel was nice insurance - gave me security.3) Go SLOWWWWW! Don't overfill your printheads. Heat the cleaning juice by placing your filled syringe in a cup of hot water. Then, when you inject the cleaning solution, let it sit in there for an hour at least. Go do something else for a while. I did that over the course of two days. Boy, was it rewarding to be able to print perfectly in color after those two days.4) DON'T LEAVE THE CLEANING JUICE IN THE PRINTHEADS OVERNIGHT!!! By design, this stuff slowly leaks out and is absorbed by the papertowel and blotter paper. Don't let it sit too long. I think I left it sit once for 2.5 hours - there was a lot of juice! If I had left it longer, I may have had a mess.5) Set up good lighting - I had a clamping lamp shooting straight at my ink nozzles so I could see clearly as I tried to fit the syringe attachment into the nozzle - NOT EASY! I also wore my husband's strong reader glasses to help me have the clearest possible vision and a little magnification.All in all, I say GO FOR IT! It's a fair pain in the butt to resuscitate your printer, but totally worth it - and this is the right product!

From what I know, dont worry about the brand, this works on any printer where the ink is stored in one location of the printer, and moves through hoses to get to where it is put onto the paper. On my printer the ink is stored in the front right.Essentially all I did was take the syringe and little hose (threw away all of the extra pieces that didnt apply to me) filled the syringe with fluid, keep air bubbles out, take ink out, use needle nose pliers to push the other end of the little hose onto the port where the ink goes is (near the bottom of the ink for me). Now uptop open your printer to see its innards and jam paper onto the sensor switch to tell the printer oh yea this lid is closed, then begin a head cleaning, this causes the moving part to unbuckle and move about the cabin, then oncw it does BAM you unplug the printer. use your hands to gently slide the moving part into the middle and put a strip of paper towel under it, fluid will come out here from that syringe, youll wana use the gloves. Gently push fluid into the system, you dont want pressure, and letting the fluid sit and work is a good idea. How long? idk long enough to play teenage mutant ninja turtles arcade game until you beat the level with all of the fire. I probably waited 10 minutes. do not push hard. Now You may want to do all of the colors while youre at it, unless this is stressing you out, in which case just go for good enough to work. When done, remove the paper towel, plug the printer in, run a head cleaning and repeat.You should see NO air in the little hoses going to the moving peice (carriage) if so, flush more to remove all air.Now you can print that thing you needed to print months ago!

Okay, this is one of the better print head cleaning kits for my Epson WF-7710 thus far. It comes with everything one might need, even gloves (I used my own nitryl gloves by default). My only complaint was the difficulty attaching the small hose to the syringe and bottle nipple. Once attached, however, it stays firmly and without leaking.Ran about 20 cc of the solution through the clogged black printhead, the last 5 cc or so coming out clear on the paper towel used as an absorbent pad.My perfectionist eye still noticed the slight line where the printhead failed to apply the black ink. Allowed the printer to try and resolve, but the line remains. The solvent should have cleared this but did not for whatever reason. Other printheads cleared with just 5 cc of the solvent, though the yellow still required one more run of the printer's printhead cleaning routine to finally clear 100%. The other two cleared first try with about 5 cc each.Applied to my Epson WF-7710 with standard ink and badly clogged heads due to disuse. Ink used is a third party brand I have had good luck with (different review), not made or recommended by Epson.Recommended for all but badly clogged printheads (mine likely a worst case of this without ruining the printhead itself).Four stars for a good product that is complete and able to clear most of the printhead. I imagine if I used more of the black ink in the first place that particular hole wouldn't have clogged so badly.