Galvanized Raised Garden Beds Outdoor // 4×2×1 ft (2-Pack) Planter Raised Beds for Gardening, Vegetables, Flowers // Large Metal Garden Box (Gray) // Patented Tool-Free Design

PACKAGING - First, the garden beds are packed very well in a box that was about 16x16x5. I ordered 8 of these at a time - the 4x2x1 with the dark wooden top. I bought all they had. They arrived separately (different days, some in boxes and some in the original container) and all were in good shape. The metal sheets had rubber corner protectors on them, and they were nested neatly in the box with thin foam in between each panel. I had no damage in any of the 8 boxes although some of the cardboard boxes were a little worse for wear.TOP EDGE - The tops of the aluminum sheets have a rolled edge so it's not sharp. There is a coating on the aluminum as well so I think it will hold up well in the weather. They have a 3-year warranty if you sign up for it.ASSEMBLY - EASY. The hardest part was unpacking everything! The boxes were sealed tightly with tape so it took my dad a bit of time opening and removing things while I assembled the beds. The first one took me about 30 minutes, and when I got the hang of it, each one took me about 10 minutes after that. I did not install the wooden tops at this point.UNBOXING - What you get in the package is this: 6 curved panels (3 per end) and 4 straight panels (2 per side). Each panel has a hole at the top and bottom vertically along the 5 ribs. The 2nd, 3rd, and 4th rib each have a die cut "tongue" on the left side and a slot to receive the neighboring tongue on the right (SEE PICTURE). These tongues (or tabs) will need to be pushed closed once assembled. I used a wooden block to preserve my fingertips. There were 2 more bolts and nuts per box than I needed. I don't know if there are extra screws for the wooden tops yet. It came with an allen wrench which I didn't need.HARDWARE - It comes with a bolt and a long "t-shaped" nut that covers the rest of the bolt's on the inside of the container. The nuts have grooves so they are easy to tighten (SEE PICTURE). I started with the curved end pieces, aligned the three tongues with the holes then put the bottom screw in. I opted to install the bracket on the top (only for those with the wooden frame on top) with the bolt and nut.WOODEN FRAME MODEL - For those of you who get the box with the wooden frame on top, the wood is decent enough but could benefit from a light sanding before weatherproofing although it should be fine if you pass that step. The installation is a T-shaped bracket that is bolted by the stem of the T to the top hole. The flat part of the T has four holes - two for the end of one piece and two for the end of the other piece where they join. The pieces fit together like a puzzle. What made sense to me was to install the brackets on the aluminum frame first; then, on the floor, assemble the wooden frame like a puzzle, bottom side up (SEE PICTURE); turn the container upside down to align the brackets with the teeny tiny pilot holes for the short screws to screw the bracket under the wooden frame. I can't imagine how tough it could be to try and align the tops with the holes in the way they tell you to install it. It was easy to assemble right side down and flip the bin upside down and screw them together that way. I had no problems. You just need to make sure the brackets are aligned equally at the joints so you don't split the wood. The wood is soft, but if you split it, you can use wood glue and put it back together.NOTES: (1) the ones with wooden tops do not have a center support rod or wire to hold the sides together and prevent the container from bowing out. I think the wooden frame should hold it in place. (2) I would recommend sealing the 10 seams with exterior silicone sealant. Many people say food/kitchen grade so that's what I'll use. This will prevent dirt and water from leaking out the vertical seams (SEE PICTURE) - don't forget the holes. (3) I do like the bolt and nut system better than some of the other things I found with competitor products that used regular nuts or wing nuts. These seem to protect the bolt better. VERDICT: I have sealed all seams AND HOLES from the "tongues" which is a MANDATORY step if you want to keep water from leaking out the sides. I used almost 2 tubes of clear kitchen-safe exterior silicone on 8 containers. Also CAULK IT IN PLACE - the containers flex when you carry them around so that could break the seal, so just put it where you want it and caulk it there.I placed these on my concrete driveway for my garden because I didn't want crabgrass growing up into the bed. I placed a 6mm sheet of plastic to protect the concrete from staining, then I added a straw seed blanket with the photodegradable mesh as the base to hold in the dirt. Then I added a layer of mulch to help fill the bucket. After that, I had about 3 cubic feet of raised garden bed soil to add. Miracle Grow's version is about $10 a bag for 1.5 cubic feet, so you need 2 bags for each container.Overall, I am really happy with these raised garden beds so far. I'll revise my review as time goes on because there are so many options out there, and I did a lot of research before landing on this one.Photos show the installation I used for the tops, all my containers lined up, the "tongues" on the panels, the gaps without caulk, and the big nut that goes inside at the top and the bottom of each panel.

Why did you pick this product vs others?:This is one of the best beds that I have purchased! I love how easy it was to assemble with the tuck and press option and only two screws at the top and bottom all around the bed. I will definitely be ordering more from this company. I’d also be happy to be sponsored by this company if there’s ever an opportunity to collaborate.

I highly recommend these Galvanized Metal Power Coated Raised Garden Beds.I love them even more with the Color options. I choose Purple 4x2x1. I intend to plant my Onions, Potatoes and Sweet Potatoes.It was so easy to Assemble. I love the rubber trim around the top edge to minimize the chances of getting scratches on my legs.Although, I received 1 bed with a Middle Support bar made of metal and the other bed came with 2 Metal Cables for the middle support.I will have to wait and see which middle support is better and I will update my personal experience as to which one is better between the two middle support bar.I calculated that for a 4'x2'x1'= 8 cuft Soil will be needed. I decided to customize my Garden Soil with 8 cuft of soil into portions of 3/3/2, you would have three portions:Coco Coir (2 parts coco coir)2 cubic feet = 14.961 GallonsCompost (3 parts compost)3 cubic feet = 22.442 GallonsGarden soil (3 parts soil)3 cubic feet =22.442 GallonsI will be purchasing more of these Raised Garden Beds from Plant & Plot in the color Purple.I will share a photo later when I have my Garden plot completed. Here is a picture of them assembled.

Maybe I didn’t put enough thought into this one. It was smaller than I expected. Even thought it was exactly what I ordered. Arrived good. Easy set up.Just a bit small

One of the best out there. Easy to build, and feels sturdy. Easy to read instructions. Has unique little notches to press down that significantly decreases build time. I now have four of their raised garden beds . Plan on getting more in the future.

This was easy to assemble, looks great for an above ground garden planter. Cost was great compared to similar one piece planters at other DIY stores.

Fabulous product, great quality, well packaged and even supplied extra hardware. Highly recommend!

These planters are great. Easy to assemble, durable. I had raised wooden beds before and these are much better in my opinion